Making a gable roof

The advantage of a dual roof is the simplicity of the device, as well as a large variety of roofing materials that are suitable for this type of construction. In addition, dual-slope roofs are suitable for attic space. In this article, an example of a dual-slope roof for a residential house will be considered.
Making the roof starts with a power plate. This is a timber with an approximate section of 12x12 cm, which is simply placed on the edge of the brickwork. Previously, the mauerlat must be upholstered with roofing paper on both sides (the side of the bar on which he lies down and the outside facing the street). In the corners the power plate is fastened together.
There are two types of dual roof manufacturing. The first type - all structural elements are assembled directly on the roof. The second option - the farms are collected on the ground, after which they climb to the roof and are set by level. The second option is faster, since it is easier to assemble the structure on the ground.In addition, making farms on the ground, it is easier to make them the same.
So, first we are going to the first farm, which will exactly match the design of the roof. Here it is important to take into account all the dimensions and angle of the slope, since the first truss will be a template for subsequent trusses. After the first farm is ready, rafters are put on its level, the same angle of the ramp is cut, and bolts (3 pieces) are fastened on the level of the first farm. For crossbars, a board 30 mm thick is used. These elements are installed at a distance of 30 cm from each other. It is possible to collect farms with the help of nails, or screws. Although the timber for rafters can be of different widths, the most important thing is that all the farms are on the same level on the outside. Tolerance to deviations is 2 cm.
Making a gable roof

Making a gable roof

Making a gable roof

After all the trusses are assembled, they need to be raised to the roof for installation. First you need to secure the two extreme farm, then pull the fishing line. Thus, the line becomes the level at which subsequent farms are set. So that the wind does not tear the trusses, temporary mounts to the floor, as well as to each other, are used. In addition, it is required to fasten the trusses of trusses with the mauerlat with a long nail or self-tapping screw.
Making a gable roof

Making a gable roof

Making a gable roof

Making a gable roof

Making a gable roof

Making a gable roof

Making a gable roof

Making a gable roof

The next stage is the fastening of the crate.Deviations from the batten depend on the material with which the roof will be covered. A standard version is offered in the sample - the crate is 80 cm above and below. The remaining boards are mounted 40 cm apart from each other. In this case, according to the project, the length of the rafters should be 6.5 m. However, the beams that were purchased for the rafters had a length of 6 m. Therefore, fillets 70 cm each were attached to the edges of the rafters. A board 30 mm thick was used for the fillies.
Making a gable roof

Making a gable roof

Making a gable roof

After the trusses are installed, it is necessary to additionally fix the power plate. For this, the mason makes the laying on the inside of the wall, closing the mauerlat. The laying passes between rafters, thereby strengthening farms. In addition, it is necessary to tighten each second farm. This requires a wire, as well as an anchor, which are installed at a distance of at least 30 cm from the rafters. Then it is necessary to wind the rafters with the installed anchors with wire and to tighten it well.
Making a gable roof

Making a gable roof

Making a gable roof

Making a gable roof

Making a gable roof

Making a gable roof

In the attic work includes sealing side gables. In this case, the pediment is trimmed with hips with an indentation of 10 cm. (board thickness of 25 mm). The side of the roof that overlooks the street has a window, and the side that overlooks the courtyard with a door. In addition, it is necessary to hem the overhangs of the roofs with a board.It is convenient to do it with self-tapping screws, as it is inconvenient to hammer nails from below.
Making a gable roof

Making a gable roof

Making a gable roof

Making a gable roof

Making a gable roof

For the manufacture of the roof needed first-class forest. Even if the material will come across the bark, it should be cleaned with an ax, but in no case be left. In addition, all used wood material must be treated with an antiseptic for fire safety, as well as to protect against pests.

Related news

Making a gable roof image, picture Making a gable roof Making a gable roof Making a gable roof Making a gable roof Making a gable roof Making a gable roof Making a gable roof Making a gable roof Making a gable roof Making a gable roof Making a gable roof Making a gable roof Making a gable roof Making a gable roof Making a gable roof Making a gable roof Making a gable roof Making a gable roof Making a gable roof Making a gable roof Making a gable roof Making a gable roof Making a gable roof Making a gable roof Making a gable roof Making a gable roof