Buy the door now is not so cheap! Many good owners are wondering about the restoration, and the answers are here.

Do-it-yourself door restoration- not easy, but very interesting occupation because you can fantasize, experiment. Modern products are mostly hollow or of poor quality, so don’t rush to throw away old structures.

Restoration of wooden products you can do yourself, but only with patience. Updating the old door frame is not so troublesome as it seems, because even a new canvas often has to be polished or painted, and in the new door you have to cut locks or hinges.

Do-it-yourself door restoration is not an easy job, but a very creative one. To make the door leaf look as good as new, all the paint needs to be removed from it, and then level the surface with putty.

Preparation

It is recommended to restore the door frame in a separate room, and it’s best to do it outside, as during the reconstruction process it is possible to raise dust, and free space will be necessary. Tools for work:

  • electric drill;
  • hand skinner;
  • brushes;
  • building hair dryer;
  • a hammer;
  • grooving saw;
  • chisel;
  • putty knife;
  • fomka;
  • screwdriver.

To work effectively, we will need not only tools, but also some materials including:

  • primer;
  • emery with a small and large dusting;
  • special beadings used for glazed doors;
  • varnish;
  • paint;
  • platbands;
  • fittings.

Job

When all the necessary materials and tools are prepared, you can proceed to laying the door leaf in a horizontal position, after removing it from the hinges. If the removal is difficult for any reason, then you need to use the disassembly while being careful.

Upholstery, if any, should be removed, since we need the surface in its original form. After removing the upholstery material, we proceed to the dismantling of locks and handles, and if there is glass in the construction, we also remove it.

To remove the old paint, we use a hair dryer, with which we heat it up to swelling and then remove it. It is important to remember to turn off the hair dryer for a five-minute break every 15 minutes. Be careful, because the hair dryer warms up to 6,000 degrees.

Hair dryer can remove most of the paint, but not all. In some areas, you can find the remains of dried blood, for the elimination of which use a hand-skinner. We put sandpaper on the skin and carry it over the entire surface of the door, thereby eliminating any irregularities or remnants of the coating. Preparing the door leaf, you can begin to seal the cracks with a primer.

Door reconstruction

The remaining defects on the structure are eliminated last. To do this, you need putty and extra time to dry it, after which it is necessary to perform the grinding of the treated areas. For this we need medium-grained sandpaper, which needs to be moved only in the direction of the fibers.

To eliminate traces of processing, avoid diagonal or transverse strokes. When sanding is finished, it is recommended to moisten and sand it with a zero sandpaper and then putty.

Door painting

Now you should paint the door, and it is better to do it in two stages. First, matt enamel is applied to the surface, and then it is given the desired shade with special paint.Before painting the canvas must be wiped from dust.

Paint should be applied with a simple paint brush, keeping the direction along the fibers. Avoid smudges by painting the surface horizontally. After drying, the design should be turned over and repeat all the procedures, because the restoration of the doors with their own hands is quite laborious.

When the surface of the door is completely dry, it should be sanded with fine sandpaper so as not to leave microscopic particles. Now we will start toning. To do this, it is best to use a special paint that does not leave stains. The number of layers depends on the desired result - the more saturated the desired color, the more paint.

The next layer is applied after the previous one is dried and sandpaper is processed. Paint can dry 6–12 hours, it directly depends on its quality and number of layers. Practice shows that a perfectly smooth surface is obtained after two applications.

Now the door is ready, it remains only to insert the glass and fasten the fittings.This is the easiest way to restore the door, which can be done at home by yourself.

Pasting the veneer

Veneer can not only restore the door, but also to repair them. Of course, the cost of restoring the web with this material will cost more, but the appearance will be much more beautiful.

To work with veneer, we need special sheets of wood, which are produced on a glue base. We warm the veneer, glue it on the door, then fix it with a load and varnish it. It is very important that there is no empty space left under the wood, otherwise the restoration of the doors will go down the drain.

Materials

Do-it-yourself door restoration will require energy, time and financial investments from you. We will need:

  • Syndicate glue, which can be successfully replaced with a putty (it will also be useful to us);
  • veneer;
  • wood glue;
  • paper.

Instruments

To work properly with veneer, we need a certain set of tools that will help speed up the process and improve the result. So:

  • metal ruler;
  • plane;
  • syringe or pipette;
  • iron;
  • sandpaper;
  • smooth bar;
  • screwdriver;
  • carpenter's knife;
  • jigsaw.

Do-it-yourself door restoration

In order to get rid of defects use a plane, and for small flaws sandpaper will be enough. A common reason why the door has to be repaired is in cracks. To eliminate them, we will use syndeticon glue, and for its absence - putty. After processing all the cracks, the door leaf should be cleaned with sandpaper.

Now you can start cutting sheets to the size of our door. Saving time and avoiding damage to raw materials will help drawing the pattern first on the paper. For cutting sheets using a knife, and evenness of the tool on the plane will provide a metal ruler.

On the back of the sheet is applied previously prepared carpenter's glue. The door leaf is also treated with the same mixture, and then it is left for 10 minutes for impregnation. Now you can attach the veneer and walk on it with a iron heated to 50 degrees. This process is called grinding. The movements of the iron must begin in the middle and end at the edges.

If there is air under the veneer (which should not be allowed), an incision should be made in this place and the defect should be removed with a syringe.Well, the door has been restored and now we leave it for 2 hours, after which it can be safely installed back.

Decorative trims for door trim

These wooden products will help to give the door an original look, but can only be used in interior designs. First, the door must be removed and laid in a horizontal position, placing construction goats or a table under it. Now you can eliminate the irregularities for which we need sandpaper.

To remove the dust from the construction of a vacuum cleaner or enough rags. Restoration of doors with their own hands is carried out in two stages. Now we pour the soil mixture onto the canvas and leave it alone. After this kind of preparation, we cover the door leaf with varnish, using a paint roller or brush.

While the varnish dries, you can do planks, which are also treated with a soil mixture. When the primer is dry, you will need to varnish them. At this stage, mark the length of the door and pick it on the slats. It is recommended to take glue or small nails for fixing the slats.

Conclusion

Even the old doors will stand a little more if you look after them and periodically repair them.In that case, if you do not like solid doors, they can be glazed, which will give originality and originality.

You can restore the door frame at no extra cost. Original and glazed doors will radically change the room, making it lighter and more spacious.

Related news

Do-it-yourself door restoration image, picture, imagery


Do-it-yourself door restoration 51


Do-it-yourself door restoration 34


Do-it-yourself door restoration 52


Do-it-yourself door restoration 85


Do-it-yourself door restoration 6


Do-it-yourself door restoration 69